| 1. |
Remove the engine cover.
|
| 2. |
Remove the battery terminal.
|
| 3. |
Remove the air duct.
|
| 4. |
Remove the battery tray.
|
| 5. |
Remove the air cleaner.
| (1) |
Upper
|
| (2) |
Lower
| |
| 6. |
Remove the back-up lamp switch.
|
| 7. |
After removing the CKP sensor, O2 sensor and
oil pressure switch wiring bracket, separate the
connectors.
|
| 8. |
Remove the brake fluid leveling sensor
connector.
|
| 9. |
Remove the speedometer driven gear
connector. |
| 10. |
Remove the clutch release cylinder mounting
bolt.
|
| 11. |
Remove the cotter pin of the shift cable
(transaxle side).
|
| 12. |
Remove the cotter pin of the select cable.
(transaxle side) |
| 13. |
Remove the clip of the shift cable (transaxle
side).
|
| 14. |
Remove the clip of the select cable (transaxle
side).
|
| 15. |
Separate the steering column shaft
joint.
|
| 16. |
Separate the power steering oil pump
hose.
|
Be careful not to leak after
separating. | |
| 17. |
Separate the hose after removing the clip of
the power steering return hose.
|
| 18. |
Remove the upper connecting transaxle
bolt.
|
| 19. |
Separate the start motor.
|
| 20. |
Install the engine support
fixture. |
| 21. |
After removing the tire, remove the
caliper.
|
| 22. |
Remove the transaxle side cover.
|
| 23. |
Remove the transaxle side under
cover.
|
| 24. |
Separate the tie rod end.
|
| 25. |
Remove the wheel speed sensor and the knuckle
mounting bolt.
|
| 26. |
Drain the oil.
|
| 27. |
Remove the transaxle mounting
bracket.
| (1) |
Insulator bolt
|
| (2) |
Body side mounting bolt
(Upper)
|
| (3) |
Body side mounting bolt
(Side)
|
| (4) |
Transaxle side mounting
bolt.
| |
| 28. |
Remove the front roll stopper.
| (1) |
Insulator bolt
|
| (2) |
Stopper bolt (Upper)
|
| (3) |
Stopper bolt (Lower)
| |
| 29. |
Remove the rear roll stopper.
| (1) |
Insulator bolt
|
| (2) |
Stopper bolt
| |
| 30. |
Remove the drive
shaft. |
| 31. |
Remove the front muffler.
|
| 32. |
Remove the sub frame mounting
bolt.
|
| 33. |
Install the transaxle jack.
|
| 34. |
Remove the transaxle lower mounting bolt to
the engine.
|
| 35. |
Remove the transaxle
assembly. |
Installation is the
reverse of the removal.
| SERVICE ADJUSTMENT
PROCEDURES |
TRANSAXLE GEAR OIL LEVEL INSPECTION
| 1. |
Remove oil filler plug and check level with
finger. |
| 2. |
Oil level must be up to fill the hole, add oil
until it runs over. Then reinstall
plug. |
| 3. |
Replace the oil so that the transaxle gear oil
is not dirty, and so that it is of a suitable
viscosity. |
REPLACEMENT OF TRANSAXLE GEAR OIL
| 1. |
With the vehicle parked on a level surface,
remove the drain plug and drain the transaxle
oil. |
| 2. |
Replace the gasket with a new one and install
the drain plug. |
| 3. |
Add new oil through the filler plug and, fill
it to just below the plug opening.
Standard
value
Transaxle oil total capacity
:
M5BF2 : 2.15 lit
M5GF1 : 2.1 lit
MFA60 :
2.2 ± 0.1
lit
|
|
DRIVE SHAFT OIL SEAL REPLACEMENT
| 1. |
Disconnect the drive shaft from the transaxle
(Refer to "DS" group). |
| 2. |
Using a flat-tip screwdriver, remove the oil
seal. |
| 3. |
Using the special tool (09431-2C000), tap the
drive shaft oil seal into the
transaxle. |
| 4. |
Apply a coating of gear oil to the oil
seal.
|
